Damaged Clock Hands 17.5" for High Torque Movements, Black
Damaged 17.5 inch Tapered Black clock hands for high torque movements
These clock hands are slightly damaged but still in great working condition! When ordered, you will receive a set that is either slightly bent or scratched.
The measurement is from the hole where the hands mount onto the high torque shaft, to the tip. Hour hands are proportionate.
These hands are USA Made of quality aluminum. American “I’ shaft configuration.
Tips for making larger wall clocks:
1. Second hands not included - we don't recommend second hands with high torque movements as they draw too much power.
2. Want a second hand? - choose our balanced 10 inch red or black second hands that work with our Continuous Sweep (Silent) High Torque Motors.
4. These hands can be trimmed to a shorter length if you keep the hand balanced. (just put the mounting hole of the minute hand on your fingertip to check the balance) They can be spray painted another color. If you are going to trim the hand to fit a particular size clock dial, the minute hand must remain balanced. Normally people just glue the material removed right under where it was cut from. You can check the balance of any minute hand just by placing the mounting hole on your fingertip. If it lays there flat then it's balanced, but if it falls off your fingertip, it's not properly balanced.
*Product may be slightly scratched or bent
|
How do I choose the right size clock motor & hands? 2) The size of hands is based on the length of the minute hand from the mounting hole to the end of the minute hand. (Figures 3 & 4) 3) Our clock motors are sized by the thickness of the dial the movements can go through. EG. High torque Q-64 will go through up to 5/8" thick material, while standard/mini motor Q-65 will go through 3/8" thick clock faces. (Figure 1 and item "A" in Figure 2) Tip 1) If your material is too thick, consider removing some to in-set the clock. Or if your clock face material is too thin, consider adding some material behind the face so the hands will sit closer to your clock face. Tip 2) Most hands can be slightly trimmed if need be. Tip 3) Our customers also spray paint them. |
If you don't have your clock motor yet...
Click here to Choose Suitable High Torque Clock Motors that work with these hands.
Damaged 17.5 inch Tapered Black clock hands for high torque movements
These clock hands are slightly damaged but still in great working condition! When ordered, you will receive a set that is either slightly bent or scratched.
The measurement is from the hole where the hands mount onto the high torque shaft, to the tip. Hour hands are proportionate.
These hands are USA Made of quality aluminum. American “I’ shaft configuration.
Tips for making larger wall clocks:
1. Second hands not included - we don't recommend second hands with high torque movements as they draw too much power.
2. Want a second hand? - choose our balanced 10 inch red or black second hands that work with our Continuous Sweep (Silent) High Torque Motors.
4. These hands can be trimmed to a shorter length if you keep the hand balanced. (just put the mounting hole of the minute hand on your fingertip to check the balance) They can be spray painted another color. If you are going to trim the hand to fit a particular size clock dial, the minute hand must remain balanced. Normally people just glue the material removed right under where it was cut from. You can check the balance of any minute hand just by placing the mounting hole on your fingertip. If it lays there flat then it's balanced, but if it falls off your fingertip, it's not properly balanced.
*Product may be slightly scratched or bent
|
How do I choose the right size clock motor & hands? 2) The size of hands is based on the length of the minute hand from the mounting hole to the end of the minute hand. (Figures 3 & 4) 3) Our clock motors are sized by the thickness of the dial the movements can go through. EG. High torque Q-64 will go through up to 5/8" thick material, while standard/mini motor Q-65 will go through 3/8" thick clock faces. (Figure 1 and item "A" in Figure 2) Tip 1) If your material is too thick, consider removing some to in-set the clock. Or if your clock face material is too thin, consider adding some material behind the face so the hands will sit closer to your clock face. Tip 2) Most hands can be slightly trimmed if need be. Tip 3) Our customers also spray paint them. |
If you don't have your clock motor yet...
Click here to Choose Suitable High Torque Clock Motors that work with these hands.
Add to Cart
USA Made High Torque Clock Movements to Make Large Clocks (Up to 5/8" Dial Face)
Home
Wishlist
Account
Cart